dev/hda1: 0 files, 0/65463 clusters dosfsck(/dev/hda1) returned 0 FAT: "posix" option is obsolete, not supported now TIPC: Started in network mode TIPC: Own node address, network identity 1234 TIPC: Enabled bearer, discovery domain, priority 10 msrif: module license 'Cisco Systems, Inc' taints kernel. e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX device eth0 entered promiscuous mode e1000: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX device eth1 entered promiscuous mode e1000: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX device eth2 entered promiscuous mode e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX device eth3 entered promiscuous mode e1000: eth4 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX device eth4 entered promiscuous mode e1000: eth5 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX device eth5 entered promiscuous mode Initializing partition - hda: hda1 done! mkdosfs 2.11 () System tables written to disk dosfsck 2.11,, FAT32, LFN Starting check/repair pass. Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI Copyright (c) 1999-2006 Intel Corporation. Miller TIPC: Activated (version 1.6.4 compiled 17:18:15) NET: Registered protocol family 30 TIPC: Started in single node mode Using IPI Shortcut mode Freeing unused kernel memory: 156k freed Write protecting the kernel text: 1716k Write protecting the kernel read-only data: 504k Starting kernel event manager. 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. msgmni has been set to 271 io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered pci 0000:00:00.0: Limiting direct PCI/PCI transfers pci 0000:00:01.0: PIIX3: Enabling Passive Release pci 0000:00:01.0: Activating ISA DMA hang workarounds Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A loop: module loaded pcnet32.c:v1.35 21.Apr.2008 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky Uniform Multi-Platform E-IDE driver ide_generic: enforcing probing of I/O ports upon user request ide: forcing hda as a disk (980/16/32) hda: QEMU HARDDISK, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide-gd driver 1.18 hda: max request size: 512KiB hda: 524288 sectors (268 MB) w/256KiB Cache, CHS=980/16/32 hda: cache flushes supported hda: unknown partition table TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. I am able to enter into global config on my ASA 3 but on my ASA is frozen and can not enter any command at all(It is frozen every time).This is a sample of the ASA2 config: Clocksource tsc unstable (delta = 3172718007 ns) done Freeing initrd memory: 22953k freed platform rtc_cmos: registered platform RTC device (no PNP device found) highmem bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0 pages bigphysarea: Allocated 65536 pages at 0xe0400000.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |